0% APR FINANCING ON ALL RACKS - BUILD NOW. PAY OVER TIME.

0

Your Cart is Empty

Shop
Resources

HMORBBPR02

Bed Bar Accessory Panel Retrofit Kit HMOR

For HMOR Bed Bars with or without factory-welded accessory brackets. Add accessory panels with four bolt-on clamps, no welding or replacement bars required.

Panel Length
Shipping Info

Free shipping on HMOR brand products in the 48 contiguous states.

WHAT IT DOES

Expand your existing HMOR Bed Bars whether they have factory-welded accessory brackets or no welded brackets at all. This retrofit kit adds a powder-coated 12-gauge steel accessory panel using four included bolt-on mounts, without welding or replacing your Bed Bars. It can add mounting points to an otherwise bare system or provide a separate panel on compatible unused straight tube sections of a system that already has welded brackets, including the uprights of taller Bed Bars or the top horizontal tubing. Available in various lengths, the kit saves compared with purchasing the components separately.

SYSTEM COMPATIBILITY

Designed for existing HMOR Bed Bar systems constructed with 1.75-inch outside-diameter round tubing. Use the supplied 1.75-inch clamp inserts. Confirm panel length against the actual spacing of your installed bars and desired mounting points.

22-inch panels are commonly used on shorter-bed three-Bed-Bar configurations as single panels.
25-inch panels are commonly used on longer-bed three-Bed-Bar configurations as single panels.
38-inch panels are for certain Chevy Colorado two-Bed-Bar applications.
45-inch panels are commonly used as one panel spanning two Bed Bars.

OVERALL BED BAR SYSTEM LENGTH
The overall length of your HMOR Bed Bar system depends on the accessory panel configuration, the number of Bed Bars, and the mounting plate style. Accessory panels feature adjustable mounting slots, allowing the front-to-rear spacing to be shortened to accommodate different truck beds and installation preferences. Overall length is measured from the front edge of the forward Bed Bar mounting plates to the rear edge of the rearmost mounting plates.

2 Bed Bars + 38-inch panel
Standard Bed Bars (4-inch plates): 39.75 to 43.75 inches
Softopper Bed Bars (5-inch plates): 40.75 to 44.75 inches

2 Bed Bars + 45-inch panel
Standard Bed Bars (4-inch plates): 46.75 to 50.75 inches
Softopper Bed Bars (5-inch plates): 47.75 to 51.75 inches

3 Bed Bars + two 22-inch panels
Standard Bed Bars (4-inch plates): 45.75 to 51.50 inches
Softopper Bed Bars (5-inch plates): 46.75 to 52.50 inches

3 Bed Bars + one 22-inch and one 25-inch panel
Standard Bed Bars (4-inch plates): 48.75 to 54.50 inches
Softopper Bed Bars (5-inch plates): 49.75 to 55.50 inches

3 Bed Bars + two 25-inch panels
Standard Bed Bars (4-inch plates): 51.75 to 57.50 inches
Softopper Bed Bars (5-inch plates): 52.75 to 58.50 inches

MOUNTING SLOT ADJUSTMENT
Two-Bed-Bar systems have up to 4 inches of overall front-to-rear adjustment, consisting of 2 inches at each end. Three-Bed-Bar systems with two adjacent panels have up to 5.75 inches of adjustment: 2 inches at the front, 7/8 inch at each center-panel connection, and 2 inches at the rear.

IMPORTANT FITMENT NOTES
These three-Bed-Bar, two-panel examples describe overall system geometry. This retrofit kit includes ONE panel and FOUR bolt-on mounts. On three-Bed-Bar systems with two adjacent panels on the same side, HMOR recommends factory-welded accessory-panel mounts for consistent alignment. Factory-welded brackets elsewhere on the rack do not prevent adding a separate retrofit panel. A new panel can be installed with four bolt-on clamps on another compatible unused straight tube section, including the upright sections of taller Bed Bars or the top horizontal tube, provided all clamps and inserts seat fully, the panel fits, and there is adequate clearance. Do not mix factory-welded and bolt-on mounting points on the SAME panel because their different offsets prevent proper alignment. Bolt-on mounts sit approximately 1/2 to 5/8 inch farther out from the Bed Bar tube than factory-welded mounts. Contact HMOR for custom or uncertain configurations.

SYSTEM ADVANTAGE

No factory-welded accessory brackets? Add a panel without welding. Already have factory-welded brackets? Add more accessory mounting space by installing a separate panel on other suitable straight sections of your Bed Bars. The four included bolt-on clamps make this kit useful for both new accessory setups and expanding an existing welded setup, without removing current brackets or replacing the bars. All mounting points supporting each new retrofit panel must use the same bolt-on mounting style.

WHAT'S INCLUDED

One HMOR Bed Bar Accessory Panel in the selected length; four complete cast-aluminum bolt-on round-tube accessory mounts; interchangeable tube inserts including 1.75-inch inserts for HMOR Bed Bars; stainless-steel clamp screws and lock washers; Allen wrench for clamp installation. Existing Bed Bars not included.

INSTALLATION

Choose the correct panel length for the actual spacing and desired mounting location of your HMOR Bed Bars. Fit the supplied 1.75-inch inserts into the four bolt-on clamps and loosely secure them around compatible straight tube sections where all clamps and inserts can seat fully with adequate clearance. Align the four mounting points to the accessory panel without forcing it into position. Attach the panel using compatible 3/8-inch hardware, tighten the clamp fasteners evenly with the included Allen wrench, and recheck all fasteners after initial use. Existing factory-welded brackets may remain elsewhere on the Bed Bar system, but do not combine factory-welded and bolt-on mounting points to support the same panel because their offsets differ. For two adjacent panels mounted on the same side of a three-Bed-Bar system, the mounting brackets at the shared center bar must be staggered so both panels have separate attachment points and the brackets do not interfere. HMOR recommends factory-welded mounts for this two-panel, three-bar layout; this retrofit kit supplies the bolt-on mounts for one panel only.

SPECIFICATIONS

Panel lengths: 22, 25, 38, or 45 inches

Panel construction: 12-gauge steel

Clamp construction: cast aluminum

Finish: black powder coat

HMOR tubing fitment: 1.75-inch outside diameter with supplied insert

Mounting: four bolt-on round-tube clamps per one panel; no welding

Additional inserts: 1.25, 1.5, and 2-inch compatible round tubing

Panel assembly load rating: not published

FAQ

Mixed-component kit: HMOR accessory panel carries its applicable Limited Lifetime Warranty; the bolt-on round-tube clamp mounts carry their separate 1-Year Limited Warranty. Refer to the current HMOR warranty policies for terms and exclusions.

Free shipping on HMOR brand products in the 48 contiguous states.

Designed for existing HMOR Bed Bar systems constructed with 1.75-inch outside-diameter round tubing. Use the supplied 1.75-inch clamp inserts. Confirm panel length against the actual spacing of your installed bars and desired mounting points.

22-inch panels are commonly used on shorter-bed three-Bed-Bar configurations as single panels.
25-inch panels are commonly used on longer-bed three-Bed-Bar configurations as single panels.
38-inch panels are for certain Chevy Colorado two-Bed-Bar applications.
45-inch panels are commonly used as one panel spanning two Bed Bars.

OVERALL BED BAR SYSTEM LENGTH
The overall length of your HMOR Bed Bar system depends on the accessory panel configuration, the number of Bed Bars, and the mounting plate style. Accessory panels feature adjustable mounting slots, allowing the front-to-rear spacing to be shortened to accommodate different truck beds and installation preferences. Overall length is measured from the front edge of the forward Bed Bar mounting plates to the rear edge of the rearmost mounting plates.

2 Bed Bars + 38-inch panel
Standard Bed Bars (4-inch plates): 39.75 to 43.75 inches
Softopper Bed Bars (5-inch plates): 40.75 to 44.75 inches

2 Bed Bars + 45-inch panel
Standard Bed Bars (4-inch plates): 46.75 to 50.75 inches
Softopper Bed Bars (5-inch plates): 47.75 to 51.75 inches

3 Bed Bars + two 22-inch panels
Standard Bed Bars (4-inch plates): 45.75 to 51.50 inches
Softopper Bed Bars (5-inch plates): 46.75 to 52.50 inches

3 Bed Bars + one 22-inch and one 25-inch panel
Standard Bed Bars (4-inch plates): 48.75 to 54.50 inches
Softopper Bed Bars (5-inch plates): 49.75 to 55.50 inches

3 Bed Bars + two 25-inch panels
Standard Bed Bars (4-inch plates): 51.75 to 57.50 inches
Softopper Bed Bars (5-inch plates): 52.75 to 58.50 inches

MOUNTING SLOT ADJUSTMENT
Two-Bed-Bar systems have up to 4 inches of overall front-to-rear adjustment, consisting of 2 inches at each end. Three-Bed-Bar systems with two adjacent panels have up to 5.75 inches of adjustment: 2 inches at the front, 7/8 inch at each center-panel connection, and 2 inches at the rear.

IMPORTANT FITMENT NOTES
These three-Bed-Bar, two-panel examples describe overall system geometry. This retrofit kit includes ONE panel and FOUR bolt-on mounts. On three-Bed-Bar systems with two adjacent panels on the same side, HMOR recommends factory-welded accessory-panel mounts for consistent alignment. Factory-welded brackets elsewhere on the rack do not prevent adding a separate retrofit panel. A new panel can be installed with four bolt-on clamps on another compatible unused straight tube section, including the upright sections of taller Bed Bars or the top horizontal tube, provided all clamps and inserts seat fully, the panel fits, and there is adequate clearance. Do not mix factory-welded and bolt-on mounting points on the SAME panel because their different offsets prevent proper alignment. Bolt-on mounts sit approximately 1/2 to 5/8 inch farther out from the Bed Bar tube than factory-welded mounts. Contact HMOR for custom or uncertain configurations.